DIY Picture Framing for Oil Paintings

DIY picture framing is how I frame my own oil paintings at the studio bench. It took a few wonky corners to get there, but it is not difficult once you have the right two or three tools. Here are the tips I wish someone had told me, the kit I use, and a calculator for what the moulding really costs.

Framing is not rocket science

Framing is a skill, not a mystery. Once you have learned it, it is simple – and when you are starting out as an oil painter and want to offer your paintings framed, it saves you a lot of money and a lot of waiting around.

You do not need a workshop on day one. Start with a few hand tools and build the kit up over time. It is a reasonable investment for the early years of your art career, and if your work takes off and you would rather hand the framing to a professional, good tools sell on easily second-hand.

Framing is also an art of its own. The right moulding finishes a painting the way a last glaze does. The tips below are the ones I have collected at my own bench – useful for anyone starting to explore framing.

From my bench

Sliding mitre saw on a folding mitre saw stand with a home-made zero-clearance fence, set up for cutting picture frame moulding
Axcaliber mitre trimmer (guillotine) on a workbench, used for trimming picture frame mitres to an exact long point
Measuring and marking tools on a folding workbench with a plywood top used for picture framing

The kit I actually use: a sliding mitre saw on a folding stand, my Axcaliber mitre trimmer, and a folding bench with a plywood top.

This guide is for oil paintings on canvas or panel only: no glass to cut and no mount board, which keeps it simpler and a good deal safer. For drawings and prints, a ready-made frame is usually the sensible choice.

How to measure for a picture frame

painting + 3 mm gap = rebate size outside size The whole frame long point – measure this short point (inside, rebate edge) one side, seen from the front Each piece
Measure the painting, add the gap, then think in long points: the outside edge, tip to tip.
Tape measure, try square, 45-degree mitre square and marking gauge for measuring a picture frame
The measuring kit: tape measure, try square, 45° mitre square and a marking gauge.

Tip 1

Measure the painting, not the label

Canvases are rarely the size printed on them, and rarely perfectly square. Measure both ends of each side and use the bigger figure.

Tip 2

Add a fitting gap

Add about 3 mm to each dimension (1.5 mm a side). Canvas and wood move with the seasons, and a painting forced into a tight frame will bow the corners open.

Tip 3

Think in long points

Each piece is a trapezoid. The long point – the outside edge, tip to tip – is the easiest measurement to mark and check with a tape.

Tip 4

Check the rebate depth before you order

Compare the depth of the step in the moulding with the depth of your canvas. If the canvas is deeper, you will need offset clips – or a deeper moulding.

Tip 5

Opposite sides must match exactly

A millimetre between the two sides of a pair matters more than a millimetre on the overall size. Cut pairs one after the other with the same setting.

Tip 6

Work from one printed cut sheet

Write every length down once and tick each piece as you cut it. The framing calculator prints one for you.

Cutting picture frame moulding

1 Straight cutsquare, off the long length piece + 2 cm spare rest of the length 2 Mitre cut45° both ends, 2–3 mm long offcuts at both ends 3 Trimshave to the exact long point exact long point red = what each step removes (exaggerated so you can see it)
Three cuts, each one smaller than the last. The trimmer only ever takes off a couple of millimetres, which is why the corners close.

Tip 7

Straight cut first, with 2 cm to spare

Cut each piece square off the long length, about 20 mm over. A short piece is much easier to mitre accurately than a 3 m length waving about.

Tip 8

Then the mitre, 2–3 mm long

Cut both ends at 45°, leaving the piece 2–3 mm too long in total – a little at each end for the trimmer to shave off. Measure along the outside edge.

tape over the cut line mark on the tape, cut through it, peel it off saw fence kerf slot moulding sacrificial board screwed to the fence (zero clearance)
Two cheap tricks against chipped edges: tape, and a fence the blade has already cut through.
Close-up of a home-made zero-clearance fence on a mitre saw, the kerf slots showing exactly where the blade cuts picture frame moulding
My zero-clearance fence: the slots show exactly where the blade lands, at 90° and both 45° angles.

Tip 9

Tape the cut line

A strip of low-tack tape (I use green FrogTape) over the cut stops the face from chipping. Mark on the tape, cut through it, then peel it off slowly.

Tip 10

Let the teeth enter the face

Breakout happens where the teeth leave the wood. On a chop saw, cut with the face of the moulding up, so any rough edge ends up at the back where nobody sees it.

Tip 11

Make a zero-clearance fence

Once you have a mitre saw, screw a strip of MDF or ply to the fence and cut straight through it. The slot shows exactly where the blade lands, and supports the fibres so the cut stays crisp.

Tip 12

Skip the ends of the length

The first few centimetres of a length often get knocked in transit. Start your first cut a little way in.

Tip 13

Test your 45° on scrap

Cut four short offcuts and put them together. Any error in the angle is multiplied by eight round a frame, so a tiny gap here becomes a big gap later.

Tip 14

Let the blade stop

On a power saw, let the blade stop before you lift it. Lifting a spinning blade back through the cut nicks the face.

Tip 15

Use a stop block for repeats

Clamp a block to the saw stand or bench at the right length and every piece in a pair comes out the same.

Trimming the mitres

Tip 16

Trimming is the step that matters

A glass-smooth mitre is what makes a corner close. It is also the step that holds most people back – once your mitres are clean, the rest is easy.

Tip 17

Take thin shavings

Half a millimetre at a time, and a very thin last pass. A heavy cut tears; a thin one leaves the end polished.

Tip 18

Keep the knives sharp

A blunt trimmer crushes instead of slicing. Polcore is kind to the knives; hardwoods are not.

Tip 19

Check pairs back to back

Lay the two sides of a pair together. If they are not identical, trim the longer one until they are.

Tip 20

Why not sand or plane by hand?

I have tried shooting boards and sanding blocks. It is far too easy to round the end over or lose the 45°, and the two sides of a pair never quite match. A trimmer cuts them identically – that is the whole secret.

Gluing and clamping

Tip 21

Dry-fit first

Put the frame together without glue and look at every corner in good light. Fix it now, not when the glue is wet.

Tip 22

The right glue

Wood takes ordinary PVA wood glue, spread thinly on both faces. For Polcore, use the adhesive your supplier recommends for it.

Tip 23

Two Ls, then the frame

Glue two L-shapes and check each corner with a square. Then join the Ls and pull the whole frame together with a strap clamp.

Tip 24

Measure the diagonals

Corner to corner both ways. If the diagonals match, the frame is square. If not, adjust the strap before the glue grabs.

Tip 25

Wipe squeeze-out straight away

A damp cloth on the face before the glue skins. Dried glue on a finished moulding is hard to hide.

Tip 26

Leave it overnight

Then add V-nails or pins at the corners if the frame is large or the painting is heavy.

Tip 27

Hairline gap?

A wax fill stick or touch-up pen in the right colour hides it. Everybody uses them, including the professionals.

Fitting and hanging

Tip 28

Drill pilot holes

A 1.5–2 mm bit for every screw, so the moulding does not split.

Tip 29

Hold the painting gently

Turn buttons or flexible points if the painting sits inside the rebate; offset clips if it stands proud at the back.

Tip 30

D-rings a third of the way down

Cord between them with a little slack. It hangs flatter to the wall than a single hook at the top.

Tip 31

Bumpers on the bottom corners

Two small felt or rubber bumpers keep it straight and let the wall breathe behind it.

Tip 32

Label the back

Title, year, your name and website. It is useful for the owner, and a quiet bit of marketing for you.

Picture framing tools: the kit I use

No workshop needed. The saw stand and the bench fold flat, so everything packs away after a framing session. Second-hand tools are absolutely fine – a good trimmer or saw lasts for decades. Just check the blades are sharp and the fence is square.

ToolWhat I useWhat to look for
Mitre sawBosch Professional GCM 8 SJL, 216 mm sliding mitre sawAny 210–255 mm compound mitre saw. It doesn’t need to slide – sliding is a bonus for wider mouldings. Search “compound mitre saw”; second-hand is fine.
Mitre saw standTitan mitre saw stand (Screwfix)“Folding mitre saw stand” with roller supports and a stop.
Mitre trimmerAxcaliber MT1 (Axminster)The Rider mitre trimmer is the current equivalent; used Lion or Orteguil trimmers are good buys. Search “mitre trimmer guillotine”.
Framing tableWORX Pegasus folding bench with a loose sheet of plywood laid on topAny folding clamp workbench. The plywood just sits on top, so it lifts off when you need the clamps.
45° mitre squareShinwa mitre squareSearch “45 degree mitre square” – plenty on AliExpress and Temu for a few pounds.
Repeat measurementsVeritas Sliding Square (Axminster)Search “sliding square” – the blade locks at a set length, so every piece in a pair is marked the same. The diamond cut-out holds a pencil for lines parallel to an edge.
Tape measure and try squareNothing specialAny decent ones. AliExpress and Temu are fine for these.
ClampsStrap clamp and corner clampsSearch “picture frame strap clamp” and “90 degree corner clamp”.

Coming soon: photos of the corner clamps, combination square and vernier calliper.

Axcaliber mitre trimmer (guillotine) on a workbench, used for trimming picture frame mitres to an exact long point

Essential · from about £400

The mitre trimmer kit

For framing your own body of work. The trimmer is the one tool you can’t skip: it shaves both pieces of a pair exactly the same, and that is what makes a corner close. By hand it is far too easy to lose the 45°.

  • Compound mitre saw for the straight cuts and the rough mitres – it doesn’t need to slide.
  • Mitre trimmer (guillotine) – I use the Axcaliber MT1 from Axminster.
  • Folding workbench with a loose sheet of plywood on top as the framing table – I use a WORX Pegasus.
  • Tape measure, try square, 45° mitre square, strap clamp, corner clamps, glue, wax fill sticks.

Pro · £500 and up

Speed and volume

For batches, bigger work or framing for others. Buy second-hand if you can.

  • Sliding mitre saw for wider mouldings – mine is a Bosch Professional GCM 8 SJL (216 mm). The trimmer still does the finishing.
  • Mitre saw stand with roller supports and a stop for repeat cuts – mine is a Titan stand from Screwfix (about £35).
  • Zero-clearance fence screwed to the saw – see Tip 11.
  • Morso foot-operated guillotine – the big beast of framing workshops. Worth it if you have the space.
  • V-nailer or underpinner – only if you frame in volume.

Buying picture frame moulding

Tip 33

Know the minimum order

Mainline Mouldings has a £50 + VAT minimum for courier delivery, and delivery is £16 to the UK mainland (free over £120); its lengths are 2.9 m. Lion has no minimum on the UK mainland, but delivery is £12.50 (free over £195). Check both at checkout – terms change.

Tip 34

Frame in batches

A minimum order is easier to reach, and much better value, if you frame four or five paintings at once rather than one.

Tip 35

Plan around the length

Every piece needs its 2 cm spare plus a saw cut. A 2.9 m length often fits one frame of about 50 × 40 cm, with an offcut to spare. The calculator below works it out.

Tip 36

Polcore or wood?

Polcore is light, consistent and cuts cleanly and is kind to blades – ideal to start with. Wood is stronger for big, heavy work and can be waxed or stained to match.

Tip 37

Keep the offcuts

Anything over about 40 cm makes a small frame or a test corner. The short bits are perfect for checking your saw is still at 45°.

Tip 38

One moulding, many paintings

Picking one or two house mouldings makes a body of work look like it belongs together – and makes every order simpler.

Safety, briefly

Tip 39

Clamp the work

Never hold a short piece by hand near a blade. Clamp it, or use a longer piece and cut it down later.

Tip 40

Eyes and ears

Safety glasses with any power saw, and ear defenders if you are cutting a batch.

Worth looking up on YouTube

  • Setting a mitre saw to a true 45°.
  • Making a zero-clearance fence or insert.
  • Using a stop block for repeat cuts.
  • Gluing and clamping frame corners.
  • Sharpening the knives on a mitre trimmer.

Picture frame cost calculator

Put in your painting size, the moulding price and how many frames you want. It tells you how many lengths to buy, what is left over, how the minimum order works out, and how it compares with a framer's quote.

Your frames

Width (cm)Height (cm)How many

Painting sizes, edge to edge. Add as many sizes as you like – they all come out of the same order.

The moulding

Supplier quotes per metre? Multiply by the length. The example is Mainline's 46 mm Cornwall Polcore.

Order rules and extras

The minimum and free-delivery figures are on the same basis as your prices (ex VAT if the box above is ticked). Check the supplier's current terms at checkout.

Glue, V-nails, clips, D-rings, cord, bumpers. About £1.50–£3 a frame.

Compare

All figures are approximate – a rough idea of what a frame costs before you commit. Suppliers’ prices and delivery can change.

Save to list